Factory-direct switched-mode units designed with broad input tolerancing (85V–265V AC), reinforced dielectric barriers, and active surge mitigation to prevent brownout failures in Haiti.
Silicone-filled weather protection engineered for coastal signage and outdoor commercial illumination across Port-au-Prince and Cap-Haïtien.
Get Catalog
Industrial cabinet converter with precise multi-tap potentiometer balancing. Ideal for PLC control panels exposed to erratic EDH utility line sags.
Get Catalog
Heavy-gauge perforated aluminum chassis with high heat dissipation. High MTBF operation for automation nodes, CNC machines, and telecom repeaters.
Get Catalog
Class II reinforced isolation adapter optimized for satellite dishes, smart hubs, biometric security checkpoints, and commercial edge devices.
Get Catalog
Dual-switch mains compatibility with low ripple output, ideal for perimeter CCTV monitoring systems and emergency backup DC distributions.
Get Catalog
Built with high-frequency ferrite magnetics and secondary synchronous rectifiers, minimizing heat build-up inside unventilated distribution boxes.
Get Catalog
Integrated floating charge circuit designed for uninterrupted telecom switches and critical hospital instrumentation during routine grid cutoffs.
Get Catalog
Ultra-narrow form factor designed for automated manufacturing facilities, clean water treatment facilities, and food processing lines in Haiti.
Get CatalogStandard off-the-shelf commercial power supplies routinely fail when subjected to the operational reality of the Haitian energy ecosystem. Discover the engineering requirements for survival.
Sourcing electronic conversion gear in Haiti presents a unique triad of technical challenges: extreme voltage instability, prolonged blackout cycles, and high thermal-humidity exposure. The state electrical utility, Électricité d'Haïti (EDH), frequently experiences severe line sags where nominal 110V circuits drop to 80V, or surge abruptly past 160V during sudden load rejection on industrial feeders. Conventional switch mode power supplies designed for stable North American or European grids quickly experience thermal runaway in their flyback primary MOSFETs or suffer bridge rectifier punch-through under such volatile conditions.
Shaanxi Zelqo Power engineers each export SMPS batch destined for the Caribbean market with custom-engineered primary windings, enlarged bulk electrolytic holding capacitors (rated for 105°C and 450V working conditions), and upgraded metal oxide varistors (MOVs) with peak surge absorption exceeding 4.5kV. These preventative topological safeguards ensure continuous DC rails for mission-critical infrastructure, preventing costly downtime and equipment degradation.
As commercial hubs in Pétion-Ville, Les Cayes, and Delmas migrate away from unreliable diesel generators to photovoltaic/battery microgrids, our 14.6V and 27.4V UPS power modules provide clean DC buffering, keeping inverters and charge controllers operational without cycle interrupts.
Cellular base stations and microwave repeaters across mountainous corridors like Morne du Cibao face regular lightning-induced spikes. Our enclosed high-wattage SMPS units feature secondary crowbar protection and high galvanic isolation (3000VAC primary-to-secondary) for uninterrupted uptime.
Medical refrigeration clinics and cold-chain vaccine depots depend on rock-solid 12V/24V switching units. Zelqo Power supplies deliver zero-millisecond automatic transfer from mains to lead-acid or LiFePO4 batteries, preserving vaccine efficacy and operating-room telemetry.
In export processing locations like the Caracol Industrial Park and Sonapi Industrial Complex, automated garment machinery and automated conveyors require rugged DIN-rail 24VDC supplies capable of operating in non-air-conditioned tropical manufacturing sheds.
A strategic shift from low-end throwaway modules to high-grade industrial-grade power electronics is underway across Caribbean distribution networks.
Given the logistical hurdles and customs clearance time at Port-au-Prince harbor, supply chain managers favor SMPS units offering >50,000 hours MTBF. Replacing burned-out modules causes disruptive system outages that far exceed the price difference of a premium converter.
Commercial equipment must smoothly accommodate both 110V (traditional U.S.-style legacy equipment) and 220V generators. Dual-input manual slide switches or wide-range active power factor correction (PFC) units spanning 90V–264V are rapidly becoming baseline requirements.
High relative humidity paired with airborne salinity in coastal districts accelerates dendrite growth and short-circuits across bare PCB traces. Local contractors now actively demand automated acrylic or polyurethane conformal coating across internal SMPS surfaces.
Unlike trading brokers, we operate our own magnetic component design and power supply assembly workshops, ensuring verified testing protocols and custom topology builds.
Because we wind our own low-loss MnZn ferrite and silicon steel cores in-house, we customize turns ratios, shielding, and triple-insulated wire (TIW) to match specific power targets without relying on generic off-the-shelf magnetics.
Every single batch moves through 25+ dedicated QA checkpoints: LCR digital bridge testing, impulse winding verification, high-voltage hi-pot dielectric tests (3kV isolation), dynamic load regulation, and automated full-temperature burn-in chambers.
Shaanxi Zelqo Power's factory footprint, manufacturing floor, engineering staff, and trade capacity have been independently inspected on-site by Intertek. Buyers can review genuine audit credentials and test records on request.
We tailor every detail: customized terminal blocks, specialized DIN mounting clips, dual or triple isolated output rails, customized Silk-screen branding, and export-reinforced cartons built for ocean transit across the Atlantic.
Each delivery includes documented electrical test logs, efficiency curves, safety standard alignment (IEC 62368-1, IEC 61558), and high-voltage dielectric pass sheets, accelerating your local regulatory acceptance.
You work directly with dedicated power electronics engineers who review your schematics, thermal calculations, and enclosure dimensions, preventing costly engineering mismatches before manufacturing begins.
Clear, definitive answers to questions frequently asked by Caribbean electrical contractors, procurement officers, and hardware system engineers.
Our units use wide-range active PFC (Power Factor Correction) and flyback/forward ICs rated down to 85V AC without losing output regulation. Even if the EDH line sags from 110V to 90V, the secondary DC output remains within ±1% precision, preventing connected PLCs, cameras, or computers from resetting.
Yes. Backup diesel generators frequently introduce high Total Harmonic Distortion (THD), frequency deviations (48Hz–62Hz), and substantial inductive spikes when heavy loads switch. Our SMPS designs feature multi-stage common mode chokes, high-saturation inductors, and 1000V-rated input bridges that filter generator noise effortlessly.
For custom production runs (500–5,000 units), standard factory turnaround is 15–20 days. Shipments to Port-au-Prince or Cap-Haïtien typically transit via Ningbo or Shanghai to Miami/Kingston hubs, with transit times averaging 28 to 35 days. Air express is readily available for urgent engineering prototypes.
Yes. As an authentic OEM/ODM manufacturer, we can personalize your company logo, custom serial numbers, barcode labeling, and user warning plates in French, English, or Haitian Creole on both the power supply metal casing and the retail packaging box.
For Caribbean orders, we provide optional vacuum-dipped polyurethane conformal coating on all solder joints, IC pins, and passive components. For outdoor LED neon signage or perimeter illumination, our IP67/IP68 waterproof series is fully encapsulated in thermally conductive epoxy, blocking moisture and salt corrosion completely.
We maintain an accessible entry barrier for project contractors. Standard models have an MOQ starting at 50–100 units. Fully custom ODM builds (custom PCB layout, specialized metal tooling, custom secondary winding taps) typically start at 200–500 units, with fast prototype samples supplied beforehand for bench validation.
Connect directly with our engineering sales group to request comprehensive datasheets, custom mechanical drawings, or an immediate quotation for delivery to Port-au-Prince.
Get Catalog